Hot Toys – MMS202D04 - 1/6th scale RoboCop Collectible Figure
- Thread starter Gigerfan
- Start date
Help Support Collector Freaks Forum:
It doesn't look like rubber in hand.
But then again, we are expecting these any day now.
But then again, we are expecting these any day now.
Body and paint is good. It's the head / mouthplate that I'm concerned with.
I have the chair version ordered with a UK site Collectiblekitbash. It had been my intention to cancel that and order both the regular and the chair version with Timcent. But now with the totally unexpected early release of the T-800 I guess I'll keep that CK order of chair Robocop, assuming they'll get it a good bit later. The usual UK delay is suddenly of benefit.
franpincho
lol@$300
Unlikely.
Big forehead T1 is out this week, I don't think I've ever seen two figures being released this close except for "limited exclusives" (that are really not limited anyway)
dw316
Super Freak
Yeah I was surprised with that reveal... the T-800 wasn't in the last upcoming releases teaser...
Yoshi
Super Freak
What's goin on with that faceplate? Is it inserted correctly or? Somethin is makin it look awfully weird to me.
BeefEaster
Super Freak
- Joined
- Sep 4, 2013
- Messages
- 1,100
- Reaction score
- 408
it's not inserted correctly
it looks like whoever set it up didn't know what they were doing, you can even see the gap on the sides where it should set flush
it looks like whoever set it up didn't know what they were doing, you can even see the gap on the sides where it should set flush
DiFabio
Super Freak
- Joined
- Nov 11, 2008
- Messages
- 32,392
- Reaction score
- 2,929
Yeah, but the helmet looks like it's as far down as it can go.
What if it's a case where they put them in correctly and they just don't fit and jut out regardless? It happened with the Batman figures. DX 12's face looked like it was going to pop out no matter how hard you pushed the mouth in. Even DX 09 Batman had an issue with the upper portion of the faceplate jutting out.
The backs of the faces do look pretty thick, it might be a case of the production figure's faces just not fitting in there snugly.
If that faceplate was moved down lower so the chin was in the strap, like we think it should, there would be a gap at the top of the mouth where the upper lip meets the helmet.
What if it's a case where they put them in correctly and they just don't fit and jut out regardless? It happened with the Batman figures. DX 12's face looked like it was going to pop out no matter how hard you pushed the mouth in. Even DX 09 Batman had an issue with the upper portion of the faceplate jutting out.
The backs of the faces do look pretty thick, it might be a case of the production figure's faces just not fitting in there snugly.
If that faceplate was moved down lower so the chin was in the strap, like we think it should, there would be a gap at the top of the mouth where the upper lip meets the helmet.
Last edited:
Robopredinator
Super Freak
- Joined
- Nov 6, 2011
- Messages
- 952
- Reaction score
- 73
Those faceplates look goofy as hell. I don't care though - as long as the neutral one turns out OK!
franpincho
lol@$300
I'm sure it's the lighting. It's probably a proto being pictured too.
I'm trying to remain positive, god damn it.
I'm trying to remain positive, god damn it.
YankeesFanboy
Super Freak
They look goofy because they're supposed to capture RoboCop's anguished, pained, "I'm gonna drop a deuce in my titanium pants" look.
I don't think this is the proto, the one at SDCC 2013 was the proto, the mouth looked more pale. See the photo below. I think the one from STGCC is a production piece. It has those tiny tabs on the shoulders, which the proto did not have.
Surely they can't put the figure out where the face plates didn't fit the head
That would be like releasing another ed209 with a rubber dome
I'm confident this figure will be epic
Last edited:
Hologram AI
Super Freak
- Joined
- May 7, 2013
- Messages
- 10,240
- Reaction score
- 11,021
YankeesFanboy
Super Freak
Oh the horror if this figure comes out a broken mess.
I saw your name as the last one to post and, for one, brief second, I thought you were posting a teaser photo from Plastic Enemies.
YankeesFanboy
Super Freak
This kind of thing is always fun. Then and now.
franpincho
lol@$300
Pure badassery.
Similar threads
