1/6 Scale Mad Max V8 Interceptor (scratchbuild)

Collector Freaks Forum

Help Support Collector Freaks Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Making the door hinges.

mm039.jpg


The hinges are screwed to the body.

mm040.jpg


There are square tubes glued to the inside of the door panel, which the hinges slide into. This allows me to quickly remove the door panel during the build, saving me the trouble of un-screwing the hinges every time.

mm041.jpg


mm042.jpg


mm043.jpg


The doors are already a very good fit, with very little sanding to do.

mm044.jpg
 
Completely missed this thread.
Wonderful job!
Can’t wait to see the next steps.

944B9CB4-18F9-460A-BB27-F5828DB247B3.jpeg
 
Building the rear trunk opening.

mm045.jpg


Adding the outer body panels.

mm046.jpg


There is an inner frame to support the extra fuel tanks,.

mm047.jpg


With both openings cut out, the centre section was quite weak, so i added extra beams.

mm048.jpg


Fitting the frame to the car.

mm049.jpg


Fuel tanks fitted temporarily. These are made from 70mm drain pipe. They are slightly under size in diameter, but were the closest i could get.

mm050.jpg
 
Finished off the ends of the trunk frame and started making the spoiler end pieces. I made them too big at first, so cut them down.

mm051.jpg


All filled and sanded down. I also added the ridges on the rear panel.

mm052.jpg
 
As a lifelong Road Warrior fan who saw it in theaters and about 200 time since. I can say without question this is the greatest thing ever posted on this forum.

Yup, even better than Inart Aragorn.
I totally agree. The fact that this is being created from scratch and using plasticard is a remarkable feat of skill. Hats off to you Marine Boy, this is incredible work!
 
Making the air scoops on the sides. I started by gluing 10 lengths of L beams together.

mm053.jpg


Cut to the right size and taper the fins at the leading edge.

mm054.jpg


Cut a hole in the bodywork and fit.

mm055.jpg


mm056.jpg


Making the trim pieces. each one is made from 4 pieces of plasticard.

mm057.jpg


Rough shaping is done by a Dremel then sanded down.

mm058.jpg



mm059.jpg


Fitted onto the car.

mm060.jpg
 
Making the rear bumper. This starts as a strip of plasticard with square beams glued to the ends.

mm061.jpg


The end pieces are attached. They are curved to match the bodywork.

mm062.jpg


Adding the lower panels.

mm063.jpg


More square beams are used to fill in the gaps around the rear lights and the number plate surround added. Once it has all the corners rounded off, it's done.

mm064.jpg
 
Fantastic! Let me know if you need any reference photos Marine Boy for the weathering stage, I've got loads of images saved for when I eventually build my own 1/24 Interceptor model. May I please ask how you created the tryes?
 
The tyres are off-road RC car tyres. I normally look in the 1/8 scale range, to find the size I need. I will scratchbuild some wheel inserts to match the movie.
 
Making the inserts for the rear wheels. Still to do the centres.

mm072.jpg


These will just push fit in.

mm073.jpg


Building the rear inner arches.

mm074.jpg


Building the rear bulkhead.

mm075.jpg
 
Making the rear suspension. I've used flat steel bar to make functional leaf springs. There is still a lot more detail to be added in this area.

mm076.jpg


Checking the ride height is ok. The front suspension is not done yet, but it's necessary to check that the overall build is heading in the right direction.

mm077.jpg


mm078.jpg


mm079.jpg
 
Last edited:
Back
Top